Large-area BIPV curved solar tile roof array for commercial buildings by GreenMore
Home

low frequency vs high frequency inverter

low frequency vs high frequency inverter

  • What Is a Low Frequency Solar Inverter?
    What Is a Low Frequency Solar Inverter? May 05, 2025
    A low frequency solar inverter converts voltage with a transformer running at 50 or 60 Hz — the grid's own frequency. That choice sets the size of everything around it. The transformer carries the full flux swing of a 20 millisecond cycle, so it is built from laminated silicon steel, weighs tens of kilograms, and sits between the switching bridge and the AC output doing two jobs: stepping the voltage and separating the DC side from the AC. Nothing about that is modern. The topology has been in off-grid systems for decades and survives for reasons that have little to do with efficiency. What a low frequency inverter actually is The chain is short. A DC source, whether a battery bank, a PV array through a charge controller, or both, feeds a full bridge switching at line frequency. The output is a square wave alternating polarity every half cycle. The transformer steps it to mains voltage and isolates it. A filter on the secondary turns that into something close to a sine. The frequency decides the size. A transformer's core area scales inversely with frequency, because the flux it carries is the integral of voltage over time. At 50 Hz the core integrates for a full 10 milliseconds before the flux reverses; at 20 kHz, 25 microseconds. That is a factor of 400 in flux swing, and roughly the same factor in core cross-section for the same power. So the transformer in a 5 kW low frequency unit is a lump of steel and copper you can barely lift with one hand, while the one in a 5 kW high frequency unit fits in a shoebox. Both do the same electrical job. Only one absorbs a fault current for a few seconds without noticing. How the power stage works Low frequency power stage. The iron-core transformer sits in the main power path, not on a control board. Reading left to right: DC enters at the battery terminals, the full bridge Q1 to Q4 chops it into an alternating square wave at line frequency, the transformer steps it up and isolates it, the LC filter smooths the edges, and the output is a sine at 220 V. Total harmonic distortion stays under 3% at linear loads, which is what the filter is for. Two blocks sit outside the main path. The MPPT charger runs off the PV array and charges the battery independently of the inverter stage, with its own voltage window, 60 V to 145 V on the units GreenMore builds, at 98% MPPT efficiency. The control circuit handles regulation, overload decisions and protection, and drives the bridge through an isolated gate driver. Three-phase versions repeat the bridge three times and use a three-limb transformer. Above roughly 30 kW the same architecture appears as an isolation transformer bolted to a modular power conversion system rather than as a single integrated box. That is how most commercial storage systems handle it now. Isolation comes in three forms, not two The commonest specification error here is treating “high frequency” and “transformerless” as the same thing. A high frequency inverter with a ferrite transformer is fully isolated. A transformerless inverter is not isolated at all. Low frequency is a third case, isolated through iron. Topology Isolation Typical peak efficiency Where it is legal and sensible Low frequency, iron-core transformer Yes, galvanic, in the main power path 85–95% Off-grid, weak grid, motor loads, anywhere the code wants a separated DC side High frequency, ferrite transformer Yes, galvanic, through the HF transformer 97–98.5% Residential hybrid, small commercial, off-grid light loads Transformerless No. DC side is not separated from AC 98–98.5% Grid-tied string inverters, where the code permits and no battery sits on the DC bus In practice a transformerless unit is smaller, cheaper and about a point more efficient, but array and grid share a DC path. Some grid codes accept that for a pure grid-tied string inverter and refuse it where a battery sits on the DC bus, because the battery then has no galvanic separation from the mains. Low frequency never has that argument. The other half of this comparison, what a high frequency inverter is, covers the ferrite case. The short version: it keeps isolation and loses the weight, which is why it took over residential rooftop. Where low frequency is the only sensible answer Four situations keep this topology alive, and in three there is no real alternative. Situation What breaks with a high frequency unit A pump, compressor or fridge starts every day Inrush of 5–7 times rated current for several seconds. A 1.5–2× surge rating trips or refuses the start The site runs on a generator, or the grid sags under load Switching stages drop out on voltage dips that an iron transformer rides through Ambient is hot, dusty or humid, and service visits are expensive Dense electronics and small heatsinks have less thermal mass and more failure points The load cannot go dark: clinic, telecom shelter, water treatment Fewer active components, and the ones that fail can be swapped rather than replaced wholesale Low frequency wins wherever the load is unkind to the inverter. Motors, compressors and welders draw current in ways a switching stage designed for a smooth resistive load does not enjoy. GreenMore's own low frequency line covers 4.8 kW to 10 kW in four models, the range where borehole pumps, small cold rooms and rural clinics sit. The 15 kW off-grid project in the Philippines and the Thai off-grid home systems are both built on it. For larger work the same isolation is bought as a separate transformer in front of a transformer-based PCS up to 250 kW, or inside an isolated commercial PCS. Surge capacity comes from iron, not from firmware A transformer stores energy in its magnetic field while energised. The quantity is small per cycle, since the field builds and collapses twice every 50 Hz cycle, but the thermal mass behind it is not. A 40 kg lump of steel and copper takes minutes to heat, so a current that would destroy a semiconductor junction in milliseconds only warms the winding. That is the whole mechanism. It is not a software feature and cannot be emulated by a bigger capacitor bank.   Low frequency High frequency Surge rating 3–5× rated 1.5–2× rated Surge duration 10–20 seconds 3–5 seconds Sustained overload 125% for 10 min, 150% for 1 min About 110% for 30 s, 120% for a few seconds Thermal time constant Minutes, dominated by transformer mass Seconds, dominated by junction and heatsink Take a real case. A 3 kW borehole pump draws 15 kW to 21 kW for the two seconds it takes to reach speed, because a direct-on-line motor pulls five to seven times rated current while the rotor is at slip. A 5 kW low frequency unit rated at 3× delivers 15 kW for ten seconds and starts it. A 5 kW high frequency unit rated at 2× delivers 10 kW, falls short, and trips. The gap is not a marketing number. It is the difference between a pump that runs and a pump that needs a soft starter bolted on, and a soft starter costs money and adds a failure point. What the extra weight actually costs The weight is the part buyers underestimate. GreenMore's GM-DP range runs 38 kg at 4.8 kW and 58 kg at 10 kW, in a case 512 by 320 by 136 mm. A high frequency hybrid of the same rating is typically 10 to 15 kg. That difference changes how the unit is installed. Model Rated power Peak efficiency Weight Max charge current GM-DP048 4,800 W 85% 38 kg 29 A GM-DP064 6,400 W 85% 42 kg 38.8 A GM-DP080 8,000 W 88% 51 kg 48 A GM-DP0100 10,000 W 88% 58 kg 60 A Fifty-eight kilograms is one person plus a trolley, or two people on a stair. It is not a wall-hung unit unless the wall is concrete and the bracket is specified for it. In a rooftop plant room it changes the delivery route; in a container it changes the mounting frame. None of that argues against the topology, but each item costs money. The weight is also where the surge capability lives. Nothing here is light and rides through a motor start at the same time, because the mass doing the work is the mass you carry up the stairs. Off-grid kits that pair these units with a controller and a battery bank, like the off-grid power kit, quote the shipping weight for that reason. The efficiency gap, in kWh and in money Low frequency units are less efficient, and pretending otherwise helps nobody. The GreenMore range peaks at 85% to 88%. Comparable high frequency hybrids peak at 97% to 98.5%, and transformerless string inverters sit at the top of that band.   Low frequency (GM-DP) High frequency hybrid Transformerless string Peak efficiency 85–88% 97–98.5% 98–98.5% At 50% load 82–85% 96–97.5% 97–98% At 20% load 75–80% 90–94% 92–96% No-load draw 20–30 W 8–15 W 5–10 W Ten points sounds fatal until it meets a load profile. A house spends most hours below 30% load, where the gap is widest, so the loss is real. An off-grid site with a pump and a cold room sits between 40% and 80%, where the gap narrows and the pump start decides everything. Put numbers on it. A 10 kW array producing 1,300 kWh per kWp makes 13,000 kWh a year. Eight points is 1,040 kWh, which at €0.25/kWh is €260 a year, or €2,600 over ten years, against a price difference of €300 to €600. On a grid-tied house with a smooth load the high frequency unit wins on lifetime cost. The calculation flips where the load is a motor. A soft starter and the callouts it prevents, or a failed pump start in a village at 2 a.m., cost more than €2,600 over a decade. Efficiency is a running cost. A failed start is an event. Life, and what can be repaired The transformer has no wear-out mechanism in the ordinary sense. Copper and laminated steel do not degrade on a temperature curve the way an electrolytic capacitor does, and a transformer that fails can be rewound rather than scrapped — a routine service in the power industry, not a specialist rescue. What wears out is everything around it: DC-link capacitors, cooling fans, relays, the control board. Those are the same components a high frequency unit carries, on the same schedule. The honest claim is not that low frequency inverters never fail. It is that the expensive, hard-to-replace part lasts longest, and that field life of 10 to 15 years is routine against 5 to 8 for high frequency designs. Two conditions change that. A unit in a sealed cabinet in direct sun runs its capacitors hot and will not see fifteen years whatever the topology. A unit in a ventilated room at 30°C will. And a site where a replacement takes three weeks should weight repairability higher. For the sizing side, how to buy a home energy storage system walks through the load calculation, and storage inverter versus off-grid inverter covers the functional split that trips up tender documents. What to specify Two certification questions get asked as one. Safety approval covers the equipment; grid-code approval covers how it behaves on a network. An off-grid unit needs only the first. A grid-tied unit needs both, and the second is market-specific. Standard Scope Region IEC 62109-1 Safety of power converters for PV systems, up to 1,500 V DC International IEC 62109-2 Particular safety requirements for inverters, used with Part 1 International IEC 61727 Characteristics of the utility interface for PV systems International IEC 62116 Anti-islanding measures for grid-connected converters International IEC 61000-6-1 / -3 EMC immunity and emission, residential and light industrial International EN 50549-1 Connection of generating plants to LV networks, Type A and B Europe VDE-AR-N 4105 German LV grid connection, below 135 kW Germany UL 1741 SA / SB North American grid support and smart inverter functions US, Canada IEEE 1547-2018 Interconnection of distributed energy resources, 60 Hz US, Canada The IEC entry for Part 2 sets out the scope: grid-interactive, stand-alone and multi-mode inverters, including battery units. For the array side, the DOE PV primer covers module and string basics. Beyond certification, four numbers belong in a specification and usually are not. Surge rating in multiples of rated power and in seconds. The sustained overload curve. The battery voltage window, which decides whether the unit works with the pack you have. And transformer isolation, stated explicitly, because it is the one item a supplier can quietly drop to hit a price. On efficiency, ask for the weighted figure and the load points it was measured at. The weighting formulas are published, and a peak number says nothing about a unit that will spend its life at 25% load. The home and commercial ranges show the two ends in practice; for a specific load list, send it over. Frequently asked questions Is a low frequency inverter always better than a high frequency one? No. It wins on surge, isolation and repairability, and loses on weight, size and eight to ten points of efficiency. For a grid-tied house with a battery and no large motors, high frequency is the better choice and the cheaper one over ten years. Why are low frequency inverters so much heavier? Transformer mass scales inversely with frequency. A 50 Hz transformer for 5 kW carries flux for a full 20 millisecond half-cycle, so its core must be large enough not to saturate. At 20 kHz it carries flux for 25 microseconds. That is where the 38 kg comes from, and it cannot be designed out without changing the topology. Can a low frequency inverter run a well pump or an air conditioner? Yes, and this is the case the topology exists for. Size on starting current, not running current. A 3 kW motor pulls 15 kW to 21 kW for a couple of seconds, so a 5 kW unit rated at 3× surge starts it. Sizing on the 3 kW running load gives an inverter that trips every time the pump cycles. Do low frequency inverters work with lithium batteries? Yes, but three things have to line up: the battery voltage window against the inverter's DC input range, the protocol between inverter and BMS, and whether the charge current matches what the pack accepts. The GM-DP range takes lithium, lead-acid and GEL, at 29 A to 60 A across four models. Lithium needs the BMS link to be real, not nominal. 85% efficiency sounds low. Is that a problem? It is low against a high frequency hybrid, and it is the honest figure for an off-grid unit that includes the charger, the transfer switch and the transformer in one box. A pure grid-tied low frequency inverter reaches 92% to 95%. Compare whole-system figures at your own load profile. Can a failed transformer be repaired? Usually. Rewinding is standard practice in the power industry and costs far less than a replacement unit, though it needs a workshop rather than a service van. The parts that fail first are capacitors, fans and control boards, and those are field-replaceable on most designs. Which one should I put on a house? High frequency, unless the house is off-grid with a borehole pump or a large compressor. A grid-tied house with ordinary appliances has a smooth load, no inrush events and a strong case for the lighter, more efficient unit. P Peter Lu Energy Storage Product Manager, GreenMore Works on the storage side of GreenMore's business, sizing hybrid inverters and battery systems for residential and commercial projects. Most of his time goes on matching a topology to a load profile before anyone argues about price. Updated on November 18, 2026

Subscribe To Our Newsletter

Stay up to date with GreenMore. We share new BIPV solar tile releases, product and certification updates, and field notes from our projects — no fluff, just the things that matter to installers, distributors, and system integrators. If there's something you'd like to see covered, drop us a line — we read every reply.

Copyright @ 2026 GreenMore All Rights Reserved. Network Supported

Sitemap / Blog / Xml / Privacy Policy

leave a message

leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
submit

Home

Products

WhatsApp

contact