Large-area BIPV curved solar tile roof array for commercial buildings by GreenMore
Home

commercial battery sizing

commercial battery sizing

  • Sizing a Commercial Battery: kW First, Then kWh
    Sizing a Commercial Battery: kW First, Then kWh Mar 27, 2026
    Most battery sizing advice answers one question: how many kWh does a house need. A factory, a cold store or a shopping centre is a different problem. There the electricity bill has two halves, and a battery that fixes one half can leave the other exactly where it was. Getting the number right means sizing power and energy separately, then checking both against the hardware that actually exists. A Commercial Bill Has Two Lines, Not One The first line is energy: how many kWh you pulled, priced by time-of-use period. The second is demand: the highest average power you reached inside a billing window, usually 15 or 30 minutes, charged at a rate per kW. A third line often hides underneath, a ratchet clause that holds your billed demand at the highest figure of the last six or twelve months, so one bad afternoon in July sets the price for the rest of the year. On many industrial tariffs the demand line is the expensive half, and it is the half a battery cuts most directly. This is why a 100 kW / 241 kWh cabinet can pay for itself on a site that consumes several megawatt-hours a day. It is not selling kWh. It is holding a ceiling on kW. Home sizing collapses those two lines into one number because a house peaks at a few kilowatts and the spread between peak and base is small. If you are working on a house instead, the calculation is simpler and we cover it in sizing a home battery. Read Twelve Months of Interval Data Before Choosing Anything What to ask the utility or the meter owner for Fifteen-minute interval data for twelve consecutive months, in kW rather than kWh where possible. Monthly totals are useless here; they average the peaks away. The tariff sheet itself: demand window, ratchet clause, peak and valley periods, and the reactive power charge if there is one. Transformer rating, existing spare capacity, and the protection settings at the point of connection. Any export limit written into the interconnection agreement, which decides whether surplus can be pushed back to the grid. What you are actually looking for Sort the intervals by size and look at the top hundred. That cluster is the peak. Look at when it happens, how long it lasts, and how far it sits above the rest of the day. Then look at the base load, the floor the site never drops below, because no battery can shave below that floor and still keep the lights on. Two figures come out of this exercise: the demand level you want to hold under, and the number of hours you must hold it for. Everything downstream depends on those two numbers and nothing else. The shaded band is what the battery has to cover; the dashed line is the demand level you are buying. Step One: Size the Power in kW The battery has to cover the gap between the site load and your target demand for the entire window, not just at the instant of the peak. If the load sits 100 kW above target for four hours, a converter that can only hold 80 kW will let the demand register climb back up and the saving disappears. Take a plant that peaks at 480 kW between 10:00 and 12:00, dips, then peaks again from 14:00 to 16:00. Set the target at 380 kW and you need 100 kW of continuous discharge across both windows, with enough overload headroom to follow the load rather than chase it. Our modular converters are rated for 110% long-term overload, which covers the wobble inside a window without uprating the hardware. Do not forget the transformer The converter adds to site load when it charges. A 100 kW charger sitting on a 630 kVA transformer that already carries 500 kW leaves very little room, and the charging schedule becomes a constraint rather than a setting. Either charge inside the valley period at reduced power, or accept a longer charge window. Both are workable; discovering the limit after commissioning is not. The site survey questions we ask before any C&I installation are set out in what to prepare before installing a C&I system. Step Two: Size the Energy in kWh Energy is the shaved power multiplied by the hours you hold it, then divided by the fraction of the pack you are willing to use and by the round-trip efficiency. Skip either divisor and the system comes up short on the first hot afternoon. The C-rate sets a ceiling on duration Our outdoor cabinets and containers run at a charge and discharge rate below 0.5C. That is a deliberate choice for cycle life, and it means a 100 kW unit with 241 kWh of storage holds full power for about 2.4 hours. If the site needs four hours, the answer is two units in parallel, not one unit asked to work harder. The relationship between C-rate and run time is the same one we explain in discharge rate of a lithium battery. Depth of discharge and losses LFP packs in commercial service are normally worked to about 90% usable capacity. Round-trip efficiency, converter losses plus auxiliary consumption, lands near 90% on a well-designed system. Multiply those two together and roughly four fifths of the nameplate figure reaches the meter. A 482 kWh pair therefore delivers about 390 kWh of useful work, and that is the number the payback calculation should use. A worked example Hold the 100 kW shave for four hours and you need 400 kWh at the meter. Divide by 0.9 for usable depth and again by 0.9 for round-trip efficiency, and the nameplate requirement is about 494 kWh. Two liquid-cooled cabinets at 241 kWh each, paralleled, give 482 kWh and 200 kW of discharge. That covers roughly 3.9 hours at 100 kW, close enough for a four-hour tariff window with a little load-following margin, and a third cabinet covers a longer window or a second shave period later in the day. Step Three: Check What the Grid Connection Allows A battery that is sized correctly on paper can still be refused at the point of connection. Three limits matter. The first is the transformer and switchgear rating, which caps the sum of load and charging power. The second is reverse power: many sites have a relay that trips if power flows back, and without an export agreement the battery must be set to never export. The third is the declared demand itself, because in some markets the figure you register with the utility is the figure you are billed against regardless of actual use. Our converters hold a power factor above 0.99 and current distortion below 3% on linear load, which keeps the connection compliant without adding a filter. What they cannot do is change the size of the transformer you already have. Step Four: Put a Number on the Return Before You Commit Annual saving is roughly usable energy per cycle, multiplied by cycles per day, multiplied by the value of a displaced kWh, multiplied by operating days. On a 400 kWh usable system cycling once a day at a 0.12 USD per kWh spread over 330 working days, that is about 15,800 USD a year before degradation. Substitute your own tariff; the shape of the calculation matters more than the figure. Degradation belongs inside the arithmetic Our LFP cells are rated above 6,000 cycles to 80% capacity retention, with a design life beyond ten years. One cycle a day for ten years is 3,650 cycles, roughly half the rated life, so the fade inside a normal payback period is small. Two cycles a day changes that picture and should be priced in from the start. Demand shaving and arbitrage are not the same revenue Shaving is paid by avoided demand charges, which are stable and easy to forecast. Arbitrage is paid by the spread between valley and peak prices, which moves with the market and with your own load. A system sized purely for shaving will be smaller and will cycle less than one sized for arbitrage. Running both on the same hardware is normal, but the two revenue streams should be modelled separately before the capacity is fixed. We go through the arbitrage side in how businesses use cheap electricity. Step Five: Match the Number to a Format Once power and energy are fixed, the enclosure is a question of site conditions and delivery logistics rather than electrical design. The four formats we build cover most commercial and industrial cases. Hardstanding, service clearance and cable entry decide the layout as much as the kWh figure does. Format Rated power and energy Duration at rated power Where it fits Air-cooled outdoor cabinet 100 kW, 225 or 241 kWh 2.3 to 2.4 hours Temperate sites with a clean, shaded yard and a single shave window Liquid-cooled outdoor cabinet 100 or 200 kW, 241 to 418 kWh 2.1 to 2.4 hours Hot, dusty or coastal sites, tight footprints, integrated fire suppression required 10-foot container 100 or 300 kW, 241 to 784 kWh 2.4 to 4.8 hours Longer windows where a two-pack build beats paralleling cabinets on site 20-foot container Set by the external converter, 3,762 kWh per unit Two hours and up, depending on the converter Large industrial loads and grid-side duty where the capacity is measured in megawatt-hours The cabinet and container families are described in more detail in what an outdoor energy storage cabinet is and what a container energy storage system is. If the site needs an isolated supply, the converter itself is a separate selection and is covered in what a PCS does. What Changes the Answer on a Real Site Ambient temperature Liquid-cooled cabinets are rated from −20 to +50 °C and containers from −20 to +55 °C. Air-cooled units lose usable capacity faster in a hot yard, and the loss is not linear: a week of 45 °C afternoons can turn a comfortable design margin into a system that stops shaving exactly when the site needs it most. If the site is in a hot climate, price the liquid-cooled option before assuming the cheaper cabinet will do. Fire separation decides the footprint Our containers and liquid-cooled cabinets carry an integrated perfluorohexanone fire suppression system, and local codes still set separation distances to buildings, boundaries and each other. On a congested industrial plot those distances often decide how much capacity fits, not the energy figure. Check the code before the layout is drawn, because moving a container afterwards is a civil works job. Footprint and access A liquid-cooled cabinet measures about 1,000 × 1,330 × 2,300 mm and weighs 2,200 to 3,500 kg depending on capacity. A 20-foot container is 6,056 × 2,438 × 2,896 mm and under 35 tonnes. Both need a hardstanding, a crane or forklift path, and service clearance at the front. Retrofits fail at this stage more often than at the electrical one. A diesel generator already on site If the site already runs a genset for outages, the battery can take over the short interruptions and leave the generator for long ones, which cuts fuel burn and run hours. The transfer scheme has to be designed for it, including seamless grid-to-off-grid switching where the load cannot tolerate a break. Decide this before the converter is specified, not after. Room to grow Cabinets parallel cleanly, so starting with one unit and adding a second later is practical as long as the transformer, the switchgear and the footprint were sized for the final build. Sites that expand in phases usually regret sizing the civil works to phase one. Where the Roof Enters the Same Calculation If the site also gets PV tiles, the arithmetic shifts. A kWh generated and used behind the meter avoids the full retail rate, which is usually more than the valley-to-peak spread the battery is chasing. That makes self-consumption the first revenue stream and arbitrage the second, and it changes the optimal capacity: a battery sized only for shaving will be too small to absorb a midday generation peak. The interface questions between a tiled roof and a battery are covered in how solar roof tiles pair with storage, and the commercial case for a combined roof and battery project is set out in transforming commercial buildings with solar tiles and storage. Frequently Asked Questions Can I size a commercial battery from monthly bills alone? Not reliably. Monthly bills give you energy and a billed demand figure, but not the shape of the peak or how long it lasts, and those two determine the energy requirement. Ask the utility for interval data first. If it is genuinely unavailable, a two-week temporary meter on the main incomer costs far less than an oversized cabinet. What is the difference between kW and kWh in this context? kW is how fast the battery can deliver, and it sets how much of the peak you can remove. kWh is how long it can keep delivering, and it sets how long the peak stays removed. A system with plenty of kWh but too little kW will not hold the ceiling; one with plenty of kW but too little kWh will drop the ceiling after an hour or two. How long will a 241 kWh cabinet run a 100 kW load? About 2.4 hours at rated power, less once you allow for usable depth of discharge and round-trip losses, which puts realistic delivery just under two hours. That is the figure to use when checking it against a tariff window. Should I size for demand charges or for arbitrage? Size for whichever is larger on your own data, then confirm the other still works with the same hardware. Where the demand charge is heavy, the battery will be power-rich and energy-light. Where the peak-to-valley spread is wide, it will be the other way round. Very few sites are balanced. Can I add capacity later without replacing the first unit? Yes. Cabinets and containers are designed for parallel expansion, and the added unit joins the existing EMS as additional capacity rather than as a separate plant. The constraint is physical and electrical headroom, so size the transformer, switchgear and hardstanding for the final build at the outset. Do I need a new transformer to add a battery? Usually not, but it depends on the charging power and the existing load. If the spare capacity is smaller than the converter rating, limit the charge rate in the EMS or shift charging into the valley period. Only when the site is already close to the transformer rating does a new or larger unit become unavoidable. PL Peter Lu Energy Storage Product Manager Works on C&I storage sizing and commissioning, mostly with factories and commercial sites in Europe and the Middle East. Updated on November 16, 2026
  • Powerwall 3 vs Modular LFP: What Actually Differs
    Powerwall 3 vs Modular LFP: What Actually Differs Mar 26, 2026
    Two years ago this would have been an easy article to write. Our cells are LFP, the Powerwall 2 was nickel-manganese-cobalt, and the chemistry difference carried the whole argument. That argument is over. Powerwall 3 uses LFP as well, so any supplier still selling "LFP versus NMC" as the headline difference is selling a comparison that no longer exists. What still separates the two systems is more practical: how much capacity sits in one box, who controls the inverter, how the system behaves when the grid is weak, and what happens on the day one component fails. We build the modular side of this comparison, so read it with that in mind. Where the Powerwall 3 is the better answer, we say so. What the Powerwall 3 Actually Is One wall-mounted unit, 13.5 kWh of usable energy, 11.5 kW of continuous output, LFP cells, and a solar inverter built into the same enclosure. Round-trip efficiency is quoted at 97.5%. The warranty runs ten years to 70% capacity retention. Everything is managed from one app, installed by a certified network, and supported by a single company. The 11.5 kW figure is the part installers tend to underestimate. It is enough to carry a whole house with a heat pump running and an EV charging at the same time, without stacking units. Very few residential batteries in this class can do that from a single enclosure, and it changes what "whole-home backup" means in practice. Putting the solar inverter inside the battery also removes a box from the wall, a set of DC isolators, and one more thing that can fail or be wired wrong. On a straightforward new installation with a straightforward roof, that is genuine value, not marketing. What a Modular LFP Platform Is A modular system is the opposite arrangement. The battery is a stack of 5.12 kWh modules, each around 49 kg, that can be combined to somewhere between 5 and 40 kWh depending on the family, and paralleled further where the site needs it. The inverter is a separate purchase, chosen from whatever the installer already trusts. Nothing in the design is fixed except the module size. That flexibility cuts both ways. It means the capacity can follow the load, and it means someone has to do the matching work. A modular system is a better fit for an engineer and a worse fit for a homeowner who wants one phone number. Where the Powerwall 3 Is the Better Answer On a stable grid, in a market where Tesla operates, for a homeowner who wants the installation to be somebody else's problem, the Powerwall 3 is a sensible choice and we do not pretend otherwise. Specifically: One vendor, one warranty document, one support line. When something goes wrong there is no argument about whose part caused it. High continuous power from a single unit, which matters for heat pumps and EV charging. An integrated solar inverter with multiple MPPTs, which suits a roof split across several orientations. A mature installer network in North America, Australia and parts of Europe, with spares on the ground. Firmware and monitoring that have been through years of field use at scale. If those five points describe the project, the premium buys something real. The comparison only turns when one of them stops being true. Where a Modular Platform Wins Matching capacity to the load, not to the box A fixed 13.5 kWh unit gives a household two options: enough, or not enough. A house that needs 18 kWh buys two units and pays for 27, or buys one and runs short in February. Modules in 5.12 kWh steps land closer to the actual number, and the arithmetic behind that number is worth doing properly rather than guessing. We set out the method in sizing a home battery. Who owns the inverter This is the difference that matters most to installers. A single-vendor system ties the battery, the inverter and the monitoring to one supplier. A modular battery works with more than twenty inverter brands over CAN, RS485 and RS232, which means an existing hybrid inverter can stay, a preferred brand can be specified, and a site with unusual three-phase requirements can be built around components that already fit. For a distributor, that also means the battery can be stocked against several inverter lines instead of one. The role of the inverter in the overall design is covered in what an energy storage inverter does. Behaviour on a weak grid Across parts of Africa, the Middle East, Southeast Asia and rural southern Europe, the supply is not a laboratory waveform. Voltage sags through the afternoon, frequency wanders, and outages arrive without warning. A modular battery paired with a hybrid inverter can be configured for the local envelope: wider voltage windows, generator assist, and an off-grid output that forms its own supply rather than waiting for a clean grid to return. Our units are rated from −20 to +50 °C and built on LFP cells rated above 6,000 cycles to 80% capacity, with twelve abuse tests including nail penetration and compression, and a thermal runaway threshold above 800 °C. Those numbers matter more in a 45 °C plant room than in a temperate garage. The wider picture is in why weak-grid regions are adopting home storage. Service and spares When a module fails in a modular system, one 49 kg module is replaced and the rest of the bank keeps working. When a fixed unit fails out of warranty, the whole enclosure comes off the wall, and shipping a 130 kg assembly across a border is a different kind of problem from shipping a module. For anyone holding stock in a market far from the factory, that difference decides how many units they can afford to keep as service cover. Sourcing and lead time outside North America Availability is part of the specification. Where the brand-name unit ships from a regional warehouse with a waiting list, a modular platform ships from stock in the volumes a distributor actually orders. Our battery families carry CE, IEC 62619, UN38.3 and RoHS, which is the document set most non-North-American markets ask for at the port. Modules go in and out one at a time, which is the point of the format. The Numbers Side by Side Same job, different number of boxes on the wall. Parameter Powerwall 3 GreenMore modular LFP Chemistry LFP LFP Usable energy per unit 13.5 kWh 5.12 kWh per module, families up to 40 kWh Continuous power 11.5 kW from the unit itself Set by the paired inverter, typically 3 to 15 kW Round-trip efficiency 97.5% at system level Depends on the inverter paired; cell and pack losses are comparable Solar input Integrated inverter, multiple MPPTs Separate hybrid inverter, MPPT efficiency up to 98% Inverter choice Single vendor 20+ brands over CAN, RS485 and RS232 Expansion Within the vendor's own range 1 to 10 modules in parallel, 5 to 50 kWh on the stacked series Cycle life Not published as a cycle count; capacity warranty to 70% at ten years Above 6,000 cycles to 80% capacity, design life beyond ten years Operating temperature −20 to +50 °C −20 to +50 °C Enclosure Outdoor-rated wall unit IP54, wall-mounted or floor-standing Standard warranty Ten years Three years Certification set North American listing CE, IEC 62619, UN38.3, RoHS What the Table Cannot Tell You Warranty years are not the same as cycle life The table says ten years against three, and that line deserves an explanation rather than a footnote. A warranty is a commercial promise backed by a balance sheet. Cycle life is a physical property of the cells. Our modules are rated above 6,000 cycles to 80% capacity, which at one cycle a day is more than sixteen years of service, and the three-year term is what we put in writing today. A buyer who needs ten years of contractual cover should ask for it, in writing, and price it into the comparison. On a distributed product sold through partners in a dozen markets, extended cover is a negotiated commercial term, not a line on a specification sheet. Anyone who tells you otherwise has not read their own warranty document. The installer matters more than the datasheet A well-installed mid-range system outperforms a badly installed premium one, every time. Commissioning quality, torque on the DC terminations, the state of the earth bond, and whether anyone checked the string voltage on a cold morning decide whether the system survives its first winter. Neither brand can put that in a table. Monitoring and firmware A single-vendor system ships with one app that has been through years of field use, and that polish is real. A modular system runs on the monitoring the paired inverter provides, plus our own app for the battery, which means two screens in the worst case and one in the best. Ask to see both before you buy, on a phone rather than a brochure, and check that the data you need for a warranty claim is actually logged. Spares and response time Ask what happens on day 1,400. Who holds the replacement, how long does it take to arrive, and does the homeowner lose backup while they wait. The answer depends on the distributor in that country, not on the factory. How to Compare Two Quotes Properly Four things turn a brand argument into an arithmetic one: Cost per usable kWh, not per unit. Divide the installed price by usable capacity, not by nameplate. Boxes on the wall. Count every inverter, gateway, meter and isolator, then count the labour hours each one adds. MPPT capacity against the actual roof. A roof split across four orientations needs four trackers, whatever the battery can do. The price of one spare module or one spare unit, and the lead time to get it. Take two illustrative quotes for the same house. One supplies a 13.5 kWh unit with an integrated inverter. The other supplies 20.48 kWh of modules plus a separate 6 kW hybrid inverter. Divide each installed price by usable capacity and the comparison stops being about brands: the second system may cost more in total while costing less per usable kWh, and it delivers five kilowatt-hours more storage. Whether that is the right trade depends on the load profile, but at least the two numbers are on the same footing. Run those four on two real quotes and the decision usually makes itself. The general framework for choosing between systems is in what the best home battery actually depends on, and the voltage platform question that trips up more retrofits than any other is covered in 48 V or 512 V. If the project involves a roof, the tile side is covered in how solar roof tiles pair with storage. Frequently Asked Questions Does Powerwall 3 still use NMC cells? No. Powerwall 2 used nickel-manganese-cobalt; Powerwall 3 moved to LFP. Any comparison that claims an LFP advantage over Powerwall 3 is arguing against a product Tesla no longer sells, and it is worth being sceptical of the supplier making that claim. Is 13.5 kWh enough for a whole home? For overnight consumption in a typical house without electric heating, usually yes. Add a heat pump, an EV charged at night, or a requirement to ride through a full day of outage, and it stops being enough. The honest answer comes from the load profile, not from the capacity figure. Can a modular battery work with the inverter already on the wall? In most cases yes, provided the inverter is hybrid or the battery is AC-coupled. Protocol compatibility covers more than twenty brands, and the practical check is the battery communication protocol the inverter expects, not the brand name on the case. Can capacity be added later? On a modular system, yes. Modules can be added up to the parallel limit of the series, typically 1 to 10 units and 5 to 50 kWh on our stacked range. On a fixed unit, expansion means a second complete unit and a second connection point. Our stacked battery range and the 6 kW hybrid all-in-one both work this way. Which system suits a weak grid better? A modular battery paired with a hybrid inverter, in most cases, because the inverter can be chosen for the local voltage and frequency envelope and configured for generator assist. A single-vendor unit is designed around one grid code and one market, which is an advantage where that market is yours and a limitation where it is not. PL Peter Lu Energy Storage Product Manager Spends most of his week on capacity calculations and inverter matching, and answers more comparison questions from installers than from homeowners. Updated on November 16, 2026

Subscribe To Our Newsletter

Stay up to date with GreenMore. We share new BIPV solar tile releases, product and certification updates, and field notes from our projects — no fluff, just the things that matter to installers, distributors, and system integrators. If there's something you'd like to see covered, drop us a line — we read every reply.

Copyright @ 2026 GreenMore All Rights Reserved. Network Supported

Sitemap / Blog / Xml / Privacy Policy

leave a message

leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
submit

Home

Products

WhatsApp

contact