Large-area BIPV curved solar tile roof array for commercial buildings by GreenMore
Home Blog

Three-Curve Solar Tiles: CIGS and Back-Contact Compared

Three-Curve Solar Tiles: CIGS and Back-Contact Compared

May 07, 2026

Three-curve solar tiles are the product most people mean when they picture a solar roof that does not look like solar. Instead of fixing flat panels over an existing covering, these tiles follow the profile of traditional curved roof tiles, interlock course by course, and generate electricity as part of the building itself.

GreenMore makes them in two technologies. This guide covers how each one is built, how they compare on published figures, and where each is the right choice. The electrical side of a tile roof — strings, inverters and storage — is covered in our article on how solar roofing tiles integrate with BIPV systems.

What a Three-Curve Solar Tile Is

A three-curve tile has three parts working together: a curved, load-bearing glass shell, photovoltaic cells laminated inside it, and an interlocking edge that overlaps the neighbouring tiles. It is fitted like an ordinary roof tile — laid in courses from the eaves up, fixed to battens or rails, with the side and top edges overlapping the course below.

That overlap is the key difference from a flat panel. Rain runs down and over the joints rather than through them, EPDM strips seal the compressed edges, and a waterproof underlay below provides a second line of defence. The result reads as one continuous roof surface, which is why three-curve tiles are used for BIPV projects where appearance matters as much as output.

A single black jade CIGS three-curve solar tile, showing the curved glass shell and interlocking edge.

A CIGS three-curve tile in black jade: curved glass shell, cells laminated inside, interlocking edge on both sides.

The Two Technologies We Actually Make

GreenMore produces three-curve tiles in two technologies. They share the same curved-glass construction and fixing method but use different cell materials, so they suit different roofs and climates.

  • CIGS thin-film three-curve tiles — our long-standing range, made since 2019.
  • Back-contact (BC) three-curve tiles — our higher-efficiency range, introduced in 2025.

We are sometimes asked about other cell types such as TOPCon. We do not currently make a three-curve tile in that technology, so we would rather say so than list an option we cannot actually supply. If a project specifically calls for it, tell us and we will discuss it rather than relabel another product.

A chart of record research cell conversion efficiencies by photovoltaic technology from 1975 onwards.

Record research cell efficiencies by technology. Silicon curves sit above thin film, which is the gap that back-contact cells close on a roof.

1. CIGS Thin-Film Three-Curve Tiles

CIGS stands for copper indium gallium selenide, a thin semiconductor film deposited on glass rather than a cut silicon wafer. Thin-film cells are uniform in colour, respond well in diffuse and low-angle light, and lose a little less output as they get hot — qualities that suit a curved, dark roof.

Parameter Published value
Tile power 25–32 W per tile, by colour
Power per square metre 100–105 W/m² in black jade; 77–98 W/m² in the other colours
Dimensions 720 × 500 × 32 mm, glass thickness 7.5 mm
Weight 6.6 kg per tile; about 21.5 kg/m²
Glass Semi-tempered double glass, transmittance above 91.5%
Frame Aluminium alloy 6063-T5
Front static load 5400 Pa
Wind resistance Tested to 177 km/h on the double-glass installation system
Fire rating Class A
Operating temperature −40 °C to +85 °C
Maximum system voltage 1000 V DC
Junction box and connectors IP67, MC4
Warranty 25-year linear power; 10-year product
Standards EN 14782, EN 1090-1, ISO 9001, ISO 14001, CE

Colour affects output more than buyers expect, because the tint sits in the glass above the cells. Black jade is the highest-output option and the default for most roofs; brick red, green wave and smoky grey give up between 10 and 25 percent of the output for the colour, which is a fair trade on a heritage building and a poor one on a roof that has to hit a generation target.

Where CIGS tiles fit best

CIGS tiles are the natural choice for cultural and tourism buildings, heritage-style and curved roofs, villas and lightweight structures — anywhere a uniform dark finish and a traditional profile matter. They also hold up well in regions with a lot of diffuse light and in coastal settings, and they are offered in several colours to match the building.

One technical point for engineers: thin-film generators have different earthing requirements from crystalline arrays. CIGS systems are normally run with an isolating inverter and a defined earthed pole, following the applicable standard. We specify this in the system design rather than treating all inverters as interchangeable.

CIGS three-curve solar tiles laid on a pitched roof, reading as a continuous tiled surface.

CIGS three-curve tiles on a pitched roof. From the street the surface reads as tile, not as an array.

2. Back-Contact (BC) Three-Curve Tiles

Back-contact cells move all the electrical contacts to the rear of the silicon cell, so there are no metal lines on the front surface. More of the front is available to absorb light, the appearance is a clean, deep black, and conversion efficiency is considerably higher. This is our premium, high-output range for a curved roof.

Parameter Published value
Models GM-HW37BC / GM-HW42BC / GM-HW50BC
Tile power 37 / 42 / 50 W
Module efficiency Up to 24.1%
Power tolerance 0 to +3%
Dimensions 720 × 500 × 32 mm
Weight 6.5 kg per tile
Front static load 5400 Pa
Fire rating Class A
Power temperature coefficient −0.26% per °C
Maximum system voltage 1000 V DC, 30 A fuse
Junction box and connectors IP67, MC4
Warranty 25-year linear power; 10-year product
Standards EN 14782, EN 1090-1, ISO 9001, ISO 14001, CE

Where BC tiles fit best

BC tiles are aimed at high-end residential roofs and new builds where the owner wants the curved-tile look but more output per square metre. The front is clear of busbars, so the roof has a very consistent deep-black finish, and the higher efficiency means a given roof area covers more of the household's use. They carry the same warranty terms as the rest of the tile range: 25 years on power, 10 years on the product.

A BC three-curve solar tile with a deep black front surface and no busbars.

Back-contact cells leave the front free of busbars, which is why the surface reads as one black plane.

CIGS vs BC at a Glance

Feature CIGS thin-film Back-contact (BC)
Cell material CIGS semiconductor film on glass Crystalline silicon, contacts at the rear
Tile power 25–32 W 37–50 W
Output per square metre 100–105 W/m² in black jade, lower in other colours Higher, up to 24.1% module efficiency
Appearance Uniform, four standard colours plus custom Deep black, no front lines
Diffuse and low-angle light Strong Good
Best for Heritage, tourism, curved and coastal roofs Premium residential and new builds

The honest trade-off is the same for both: a three-curve tile costs more per watt than a conventional framed panel, and the curved profile generates less per square metre than a flat module. On a new build or a re-roof — where the tile replaces the covering rather than sitting over it — the comparison should be against the cost of the roof plus an add-on array. If a sound existing roof only needs the cheapest generation, conventional panels remain the sensible choice.

Choosing Between CIGS and BC

Most project decisions come down to three questions, and they are worth answering in order.

Start with the roof, not the module

If the roof is on a listed or heritage building, or the planning condition is about appearance, the colour range and the profile usually decide it before efficiency is discussed. CIGS is the only one of the two offered in red, green and grey; BC is black. On a roof nobody sees, that constraint disappears and the decision moves to output.

Then the output the roof has to deliver

Work backwards from annual consumption or from a target capacity, not from the tile datasheet. Divide the target by the output per square metre of the actual colour and technology, add the unusable edge zones, and see whether the available roof area is enough. Where the roof is tight, BC's higher output per square metre is usually the difference between meeting the target and not.

Then the electrical design

The two technologies behave differently at system level. CIGS strings run at low voltage and higher current, and thin-film arrays are normally earthed through a defined pole with an isolating inverter. BC tiles are crystalline silicon with a much lower power temperature coefficient (−0.26% per °C), so they hold more of their output on a hot roof and can use conventional transformerless inverters. Neither is a problem; they are simply different designs, and the inverter has to match.

If you send us the building type, roof area, location and target generation, we will come back with a specific configuration rather than a recommendation to buy the more expensive tile.

Adding Storage and the Rest of the System

Three-curve tiles generate direct current, which an inverter converts to grid-compatible alternating current. Tiles are grouped into strings sized to the inverter's voltage window across the local temperature range. A grid-tied inverter exports surplus; a hybrid inverter adds a battery connection.

Adding a battery lets the roof store midday generation for the evening, run selected circuits during an outage and increase the share of generation used on site. The battery is sized from the loads and the hours of backup required, not just from the array size. Our home energy storage range lists the supported capacities, and we supply complete solar-plus-storage packages when a project needs them.

As elsewhere, we keep the claim precise: a grid-tied tile roof with a battery meaningfully reduces dependence on the grid, but full off-grid independence needs a larger array, storage for poor-weather stretches and often a backup generator.

Best Roof Applications

A chart of global renewable and solar photovoltaic generation shares from 2015 with a forecast to 2030.

Solar's share of global generation, 2015 to 2030 forecast. The growth is happening on roofs, not only in utility fields.

Three-curve solar tiles are used on:

  • Residential roofs — villas and townhouses, especially on new builds or re-roofs.
  • Cultural, tourism and heritage-style architecture, where a traditional tile profile is part of the design.
  • Small commercial and hospitality buildings — hotels and offices that want a clean roofline.
  • Lightweight and curved structures that would not suit a heavy framed array.

The common thread is a building where the roof is visible and the roof surface is already a cost line. That is also where the economics work: on a new build, the tile replaces a covering that had to be bought anyway, so the premium is the difference between two coverings rather than the full cost of an array.

Frequently Asked Questions

How long do three-curve solar tiles last?

We state this through the warranty rather than a marketing lifespan. The tiles carry a 25-year linear power warranty plus a 10-year product warranty covering materials and workmanship. The inverter, battery and other non-tile components carry 3 years, stated separately.

How reliable is the waterproofing?

Waterproofing comes from roofing geometry: the tiles overlap and interlock, EPDM strips seal the compressed joints, and a waterproof underlay provides a second layer. Correct detailing at eaves, verges and ridges completes it. This is standard tiled-roof construction rather than a single seal, which is why it fails in the same places an ordinary tile roof would: at the details, not in the field of tiles.

Can three-curve tiles replace traditional roof tiles?

Yes. They are the outer weatherproof covering and a generator at once, so they replace the tiles rather than being fitted over them. A waterproof underlay still sits underneath, as it would under an ordinary tiled roof, and the tile count and batten spacing follow the same rules.

Which technology is better in cloudy or diffuse-light regions?

CIGS thin-film is usually the better match there, because thin-film cells respond well to low-angle and diffuse light. BC tiles still work in those conditions; they simply give less of their advantage away from strong, direct sun.

Which technology gives more output per square metre?

Back-contact tiles. They reach up to 24.1 percent module efficiency, against roughly 100 to 105 W per square metre for the CIGS range in its highest-output colour. Choose BC when roof area is limited and output is a priority; choose CIGS when colour choice, heritage styling or cost is the main driver.

Do the tiles need external mounting brackets?

No external racking over the roof. The tiles fix to battens or rails that are part of the roof build-up, just like ordinary tiles, and they interlock with their neighbours. The supporting structure is designed for the building's wind and snow loads.

Can they be paired with energy storage?

Yes. A hybrid inverter connects a home battery, letting you use more of the generation in the evening and keep essential loads running during outages. We supply the battery and inverter as the supporting parts of the tile system, matched to the tile array rather than chosen separately.

How do I choose between CIGS and BC for a project?

Start with the roof and the goal. Choose CIGS for heritage, tourism, curved or coastal roofs, colour matching and diffuse-light climates. Choose BC for premium residential and new builds that want maximum output per square metre with a clean black finish. If you send the building type, roof area, location and target generation, we will recommend a specific, buildable configuration.

Work With GreenMore

GreenMore is a photovoltaic tile manufacturer. Our three-curve solar tiles, photovoltaic bricks and photovoltaic curtain walls are produced in-house, in CIGS thin-film and back-contact technologies, with the inverter and battery supplied as supporting components. Tell us your project details and we will put together a real proposal matched to the local code.

Reach us through our contact page or at export@gmsolarkit.com.

Independent references

L

Luke

Product Manager, BIPV Solar Tiles

Luke manages GreenMore's photovoltaic building-material range, from the CIGS thin-film three-curve tile to the newer back-contact line. He has worked in the solar industry since 2017 and writes about designs that can actually be built, with specs and warranty terms that match what ships.

Updated on November 14, 2026

Subscribe To Our Newsletter

Stay up to date with GreenMore. We share new BIPV solar tile releases, product and certification updates, and field notes from our projects — no fluff, just the things that matter to installers, distributors, and system integrators. If there's something you'd like to see covered, drop us a line — we read every reply.

Copyright @ 2026 GreenMore All Rights Reserved. Network Supported

Sitemap / Blog / Xml / Privacy Policy

leave a message

leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
submit

Home

Products

WhatsApp

contact