Large-area BIPV curved solar tile roof array for commercial buildings by GreenMore
Home

Curved Solar Tiles

Curved Solar Tiles

  • CIGS or BC on a Curved Tile: Why TOPCon Stays Flat
    CIGS or BC on a Curved Tile: Why TOPCon Stays Flat Mar 25, 2026
    Why is the flat tile offered in TOPCon while the three-curve tile is not? It is the first technical question on most curved-roof enquiries, and the honest answer has nothing to do with which cell is better. TOPCon is the strongest mainstream cell technology on the market right now. It simply does not survive the shape. A three-curve tile makes specific demands of a cell, and those demands are what push TOPCon out of the curved range and leave CIGS and back-contact as the two answers. The product-level comparison between the CIGS and BC tiles is covered separately in the three-curve tile range; this piece is about the cell decision underneath it. One Factory, Three Cell Technologies Our range uses three cell technologies, and they sit in three different products: CIGS thin-film on the three-curve tile, 25 to 32 W per tile. Back-contact crystalline on the newer three-curve tile, 37, 42 and 50 W per tile. PERC and TOPCon on the flat tile, 75 to 100 W per tile. The flat tile is the biggest and the cheapest per watt. The curved tiles are smaller, more expensive per watt, and the only ones that work on a roof profile with a compound curve. That split is not a marketing decision. It follows from four constraints that a curved tile imposes and a flat one does not. What a Three-Curve Tile Asks of a Cell Start with the geometry. A three-curve tile covers 0.294 m² of roof, measures 720 × 500 mm, sits in a 32 mm interlocking body, and goes down at 3.4 pieces per square metre with an 85 mm head lap. The laminate has to live inside that body without changing the profile, because the profile is what keeps the roof waterproof. Then add the service conditions. The tile carries a 5400 Pa front load, has to survive being walked on during installation, and the HW32L body is tested against 25 mm hail at 23 m/s. It works between −40 and +85 °C. Laid, it weighs about 21.5 kg per square metre, which is the number a retrofit carpenter cares about. Finally, the appearance. The colour has to run evenly across a whole roof plane, not vary from pallet to pallet, because a roof is viewed as one surface. Those constraints rule out more cell technologies than buyers expect. Why TOPCon Stops at the Flat Tile Cutting a wafer cell down to tile size TOPCon is built as a full-square wafer with passivation layers on both faces. The passivation is what gives it its efficiency, and it stops at the edge of the wafer. Cut that wafer into strips and every cut face is unpassivated silicon, which is a recombination site. On a full-size module the cut edges are a small fraction of the total area, so the loss stays modest. On a tile the cell is a fraction of a wafer, and the perimeter-to-area ratio climbs steeply as the cell shrinks. The efficiency advantage TOPCon holds at wafer scale narrows once you have cut it into pieces small enough to fit inside a 32 mm tile body, and the yield loss from cutting adds to the cost at the same time. Bending the glass A TOPCon laminate is rigid. The three-curve profile is a compound curve, which means the glass itself would have to be formed, and the cells inside it still cannot bend. Formed glass is possible, but it is a low-yield process, and a rigid cell on a curved glass carries concentrated stress at the apex of the curve during a 5400 Pa load test. CIGS sits on a flexible substrate and is laminated into the curve rather than forced into it. That is the whole reason thin-film exists in this product category. Our back-contact tile takes a third route: a shaped rigid laminate specified for gentle curves only, which is why we do not offer it for tight or compound profiles. Bypass granularity on an interlocked roof A tiled roof is lapped in both directions, and shade does not fall in neat rectangles on it. A chimney, a ridge line or a dormer shades part of one tile and the top of the next. Small cells in series need bypass diodes at a fine enough granularity that one shaded tile does not drag a whole string down. More bypass means more diodes and more junction boxes inside a 32 mm body, which is already carrying an interlocking profile and a cable route. Higher current density per cell makes the mismatch cost of partial shade worse, not better. This is one of the reasons the curved products are specified with per-tile connectors and short strings rather than long runs. Where TOPCon does win, and where we use it Set the tile geometry aside and TOPCon is the best value cell on the market. A flat tile has no compound curve, so it takes standard glass and a standard lamination line, and it comes out at 75, 80, 95 or 100 W per tile, roughly 150 to 200 W per square metre, at 10.5 kg for a 1424 × 440 mm piece. Nothing in the curved range gets close on cost per watt. That is why the flat tile keeps TOPCon and the curved tile does not. It is not that one technology is superior. It is that the flat format lets TOPCon be used as designed, at full wafer size, on flat glass. The same factory, three cell routes, three different tile formats. Why CIGS Fits a Compound Curve CIGS is a thin-film absorber deposited on a flexible substrate. There is no wafer to cut, so there is no cut edge to lose, and the laminate can follow the tile profile through lamination rather than being bent afterwards. The trade is power density. A CIGS three-curve tile delivers 25 to 32 W, and between 77 and 105 W per square metre depending on colour: the black-jade finish reaches 100 to 105, brick red sits at 87 to 92, and the blue-wave and smoke-grey finishes come in at 77 to 82. Custom colours land between 82 and 98. Weight is 6.6 kg per tile, 21.5 kg per square metre laid. In exchange you get three things that matter on real roofs. It conforms to curves that a rigid laminate cannot follow. It keeps producing in diffuse light, which is why it holds up in coastal and northern climates. And its colour is a property of the film rather than a coating, so it stays uniform across a plane and does not fade at the same rate as a surface treatment. The failure mode to know about is delamination at the encapsulant edge, which is a manufacturing and installation quality issue rather than an inherent flaw; we wrote about it in CIGS edge delamination. Why Back-Contact Still Earns Its Place on a Curved Roof Back-contact moves all the metallisation to the rear of the cell, which removes the front busbars and the shading they cause. On the same 720 × 500 mm footprint as the CIGS tile, the BC tile delivers 37, 42 or 50 W, with module efficiency of 24.1% on the 50 W version and 23.9% on the other two. Fifty watts against twenty-five is roughly double the output from the same roof area, and on a project where every square metre of roof is already committed, that difference decides the array size. The tile weighs 6.5 kg, carries the same 5400 Pa front load, and comes in grey, green, red and black. The limitation is mechanical. The laminate is rigid, so the BC tile is specified for gentle curves and standard curved profiles with stable structural support, not for tight or compound curves. If the roof profile came from an architect rather than a catalogue, CIGS is the safer answer. The Three Routes Side by Side Item CIGS three-curve BC three-curve TOPCon flat Cell route CIGS thin-film on a flexible substrate Back-contact crystalline PERC / TOPCon crystalline Power per tile 25 to 32 W 37 / 42 / 50 W 75 / 80 / 95 / 100 W Power per roof area 77 to 105 W/m², by colour About 170 W/m² at 50 W Roughly 150 to 200 W/m² Size and weight 720 × 500 × 32 mm, 6.6 kg 720 × 500 × 32 mm, 6.5 kg 1424 × 440 × 18 mm, 10.5 kg Curve capability Compound and tight curves Gentle curves with stable support Flat planes only Front load 5400 Pa 5400 Pa 5400 Pa Colour range Black jade, brick red, blue wave, smoke grey, custom Grey, green, red, black Standard module finishes Warranty 25-year linear power 10-year product, 25-year power 25-year linear power Best fit Architectural profiles, light structures, retrofit, diffuse light Premium black roofs where output per square metre decides Flat roofs, terraces, cost-driven projects Reading Those Numbers Correctly Efficiency and watts per square metre are not the same figure The BC datasheet quotes 24.1% module efficiency. The same 50 W tile over 0.294 m² of roof works out to about 170 W per square metre, which is 17%. Both numbers are correct and they are not measuring the same area: efficiency is calculated on the illuminated cell area, watts per square metre is calculated on the roof area the tile actually covers, including the lap that disappears under the course above. Anyone comparing a tile against a framed module needs to use the same basis. A framed module quotes efficiency over its full aperture and covers no lap, so the two figures are not directly comparable. Use W per square metre of finished roof to size an array, and efficiency only to compare one cell against another. What the warranty actually says The back-contact curved tile carries a 10-year product warranty covering materials and workmanship, plus a 25-year power warranty. The CIGS tile and the flat PERC/TOPCon tile are covered by a 25-year linear power warranty. Ask for both documents rather than the headline figure, because a power warranty without a product warranty leaves you owning a working module on a failed roof. How We Specify It on a Project Four questions, in this order, decide the tile: Is the profile flat? Then TOPCon, and the argument is over. Is the curve compound, or is the roof structure light? Then CIGS, because the laminate has to conform and 21.5 kg/m² is a number old timber can carry. Is the curve gentle and is output per square metre the deciding factor? Then back-contact, at up to 50 W per tile. Does the client need a specific colour across a large plane? Then CIGS, where the colour comes from the film rather than a surface finish. The two curved families are on the site as the 32 W triple-arch hantile and the back-contact curved tile. If the roof is being built rather than re-covered, the sequence in how to install solar tiles applies to both. The lap is what makes the roof watertight, and it is also what takes roof area away from the array. Frequently Asked Questions Why is TOPCon not offered on the three-curve tile? Because the cell has to be cut small enough to fit a 32 mm tile body, and every cut face loses the edge passivation that makes TOPCon efficient. On top of that, a rigid laminate cannot follow a compound curve without formed glass and concentrated stress at the apex. The efficiency advantage it holds at wafer scale does not survive those two constraints. Is CIGS less efficient than crystalline? Yes, on a per-square-metre basis, and we do not pretend otherwise. The CIGS three-curve tile delivers 77 to 105 W per square metre against roughly 170 for the back-contact tile. What it buys in return is the ability to follow a compound curve, lower weight per square metre, and better output in diffuse light. Can I mix CIGS and BC tiles on one roof? Physically yes, since both share the 720 × 500 mm footprint and the same interlocking profile, and mixing is sometimes the right answer on a roof with one tight curved section and one long gentle plane. Electrically they need separate strings, because the current and voltage characteristics differ. Do not put them on the same MPPT input. Which one lasts longer? Both carry a 25-year power warranty, and the back-contact tile adds a 10-year product warranty on top of it. The practical difference is the failure mode rather than the lifespan. Thin-film failures tend to appear at the laminate edge and show up as moisture ingress. Crystalline failures tend to appear as microcracks from handling and thermal cycling. Both are installation-quality problems more often than product problems. Does the flat TOPCon tile work on a low-slope roof? It works as a roof covering at the slopes the profile is designed for, but it generates best at the tilt the array is designed around. On a low-slope roof the output per square metre falls and the economics change. That is an array design question, not a tile question. What certifications should I ask for on a curved tile? EN 14782 for the metal roofing element, EN 1090-1 for the structural component, and IEC 61215 and IEC 61730 for the electrical side, plus ISO 9001 and ISO 14001 for the factory. What those certificates actually prove, and what they do not, is set out in EN 14782 and IEC 61215. L Luke Product Manager, BIPV Solar Tiles Works across the CIGS and back-contact tile lines, mostly on projects where the roof profile was drawn before anyone asked whether a cell could follow it. Updated on November 16, 2026
  • What does GreenMore do?
    What does GreenMore do? Sep 27, 2026
    J Jimmy Wang Founder and CEO, GreenMore · BIPV solar tiles and roof systems GreenMore is a photovoltaic tile factory making building-integrated photovoltaic (BIPV) products for export. Our core product is the three-arch curved solar tile — the wave-shaped tile that sits on a roof in place of the ceramic version and generates power while it does the roofing job. Around that flagship we manufacture flat photovoltaic tiles, photovoltaic floor tiles and photovoltaic curtain walls in the same plant, and supply the solar power system and the battery that go with them. An overseas dealer, installer or EPC contractor can source the building material, the electrical balance and the storage from one team. Lamination and finishing lines at the GreenMore photovoltaic tile plant in Nanjing. We sell building materials that generate power The easiest way to understand BIPV is to contrast it with a normal solar installation. In a conventional rooftop setup, framed panels are mounted on top of an existing roof with rails and clamps. The panels and the roof are two separate things, each with its own supplier, its own warranty and its own failure modes. BIPV flips that order: the photovoltaic product is the roof. That is why we describe our tiles as three products in one — a building material that keeps the weather out, a photovoltaic module that generates electricity, and a finished surface that gives the roof its appearance. Once you accept that framing, the requirements stop being abstract. The tile has to carry wind uplift, snow load, rain and UV like any roof covering before its electrical performance matters at all. Our tiles are tested to a 5,400 Pa front static load and carry a 10-year product warranty on top of the 25-year power output warranty. The governing product standard for self-supporting metal roofing is EN 14782, and the module-level test sequence a buyer should ask for is IEC 61215. The product line Six product families, starting with the one we are known for. Three-arch curved solar tile Our flagship, and the product most of our export volume runs through. The bionic triple-wave profile follows traditional barrel and pantile roofs, so it fits villas, heritage-style and cultural buildings, resorts and courtyard homes where a flat framed panel would read as an afterthought. It comes in two cell routes. The CIGS thin-film version is a semi-tempered double-glass tile rated between 25 W and 32 W depending on colour, and it is the version architects pick when the roof has to look like a roof rather than like a power plant. The back-contact (BC) version uses monocrystalline cells at up to 24.1% module efficiency and runs from 37 W to 50 W per tile, for projects where output per square metre outranks the thin-film appearance. Both are 720 × 500 mm and weigh around 6.5 kg, so a roofer handles them the way he already handles the ceramic tile he knows. You can see the full range on the solar tiles category page. Photovoltaic curtain wall For commercial facades we supply glass-to-glass photovoltaic units built into the mullion and transom system rather than bolted onto it. A vertical elevation sees a very different irradiance profile from a pitched roof, so the module layout, the cell spacing and the transparency level are designed per elevation instead of being pulled off a catalogue page. This is the product that usually enters a project through the architect rather than the roofer, and it is the one that turns a building envelope into a generating surface without adding a second skin to the building. Flat and curved photovoltaic tiles For simpler roof planes we supply flat-laid and stacked photovoltaic tiles that replace conventional tiles with a thinner, more uniform surface. They are commonly mixed with the three-arch tile on the same roof — curved tiles on the visible front elevation, flat tiles on the larger rear planes — which keeps the appearance where it is seen and the cost where it is not. Solar floor tiles and PV bricks Our photovoltaic floor tiles are built to be walked on, with an anti-slip surface for terraces, garden paths, plazas and outdoor display areas. The same laminated construction appears as photovoltaic bricks for wall and parapet applications. Both extend the BIPV idea from the roof down to grade without exposing fragile framed panels to foot traffic. Solar power systems Tiles alone do not make a working system. We design and supply the solar side — string or micro inverters, mounting and waterproofing accessories, cabling, monitoring and the roof layout — and we pre-configure it for the grid rules of the destination country. A project that also needs a conventional ground-mount or flat-roof array can source that from us in the same order. Energy storage To make the generation usable after sunset and during outages, we offer wall-mounted and stacked home batteries and commercial battery cabinets. Storage is a supporting product rather than the main event for us, but it is what lets us hand over a complete solar-plus-storage package instead of a roof and a promise. You can see the scope on our home energy storage solutions and commercial energy storage solutions pages. Product Where it goes Cell route Output per unit Warranty Three-arch curved tile, CIGS Pitched roofs, villas, heritage work CIGS thin film 25–32 W 10 yr product / 25 yr power Three-arch curved tile, BC Same roofs, higher yield per m² Back-contact monocrystalline 37–50 W 10 yr product / 25 yr power Flat photovoltaic tile Large simple roof planes Monocrystalline 75–115 W 10 yr product / 25 yr power Photovoltaic curtain wall Commercial facades Glass-to-glass Designed per elevation Per project Photovoltaic floor tile Terraces, plazas, garden paths Monocrystalline 40 W 10 yr product / 25 yr power Home and C&I storage Indoor, outdoor, wall or cabinet LFP 5–20 kWh home, 215–372 kWh cabinet 3 yr How we work: a factory, not a trading desk GreenMore is a photovoltaic tile factory, not a trading company passing orders between third parties. The tiles — three-arch, flat, floor — and the curtain wall units are made in our own plant, from the glass and cell build-up through lamination, framing and the finished roof unit. We run the incoming and in-process quality checks ourselves and hold the certificates in our own name rather than borrowing a supplier's. The complete solar power and storage systems we supply are supporting products, integrated around the tiles we manufacture. We are a focused, growing factory rather than a giant mass producer, and that shape suits BIPV work. Custom colours and profiles are possible, order sizes stay flexible, and every batch is inspected against the agreed specification before it ships. Where a project needs the actual paperwork — EN 14782, EN 1090-1, ISO 9001, ISO 14001, CE — we send the documents, not a logo on a slide. Who we work with We are a business-to-business supplier, so we do not sell single roofs directly to homeowners. Our customers are the companies that deliver those projects: Distributors and dealers who stock solar tiles and batteries for their local market. Installation contractors and roofers who need a tile they can fit with familiar roofing methods. System integrators and EPC firms delivering villas, resorts, heritage renovations and small commercial buildings. Architects and project owners looking for a photovoltaic finish that fits the design rather than fighting it. Our core markets are Europe and the Middle East, where most of our tile volume goes. Storage and system enquiries reach us from a wider set of countries, which is why you will find those projects on this site next to the roofing work. We are a young brand and we stay selective about the partners we take on, so that each one gets supported properly. One source, fewer hand-offs The practical reason buyers come to us is coordination. Sourcing tiles from one vendor, inverters from a second and batteries from a third means three sets of specifications, three shipments and three people to call when something does not line up. We put those pieces together as one BIPV package, confirm they are electrically compatible, and stand behind the result. If the project is a metal roof or a sloped roof, our metal roof BIPV page walks through the installation approach. The full catalogue sits on the products page. Questions buyers ask us Is GreenMore a manufacturer or a trading company? A manufacturer. The photovoltaic tiles and curtain wall units are produced in our own plant in Nanjing, including lamination, framing and the finished roof unit. We do not buy finished tiles and relabel them. What is GreenMore's main product? The three-arch curved solar tile, in a CIGS thin-film version rated 25 to 32 W and a back-contact version rated 37 to 50 W. Flat photovoltaic tiles, floor tiles, bricks and curtain walls sit around it as the rest of the envelope range. Which countries does GreenMore export to? The tile business is concentrated in Europe and the Middle East. Energy storage and complete system enquiries come from a broader group of markets, including Africa and South America. Does GreenMore sell to homeowners? No. We supply distributors, installers, system integrators, EPC firms and architects. A homeowner who wants our tiles should go through the contractor handling the roof. What certifications do the tiles carry? EN 14782, EN 1090-1, ISO 9001, ISO 14001 and CE. The storage products carry CE, IEC and UN38.3. We send the certificate documents with the quotation when a project needs them. Talk to us about your project Send us the building type, roof area, country and target capacity, and we will come back with a product shortlist, a roof layout and an indicative quote. Reach us through the contact page or at export@gmsolarkit.com. Updated on November 12, 2026

Subscribe To Our Newsletter

Stay up to date with GreenMore. We share new BIPV solar tile releases, product and certification updates, and field notes from our projects — no fluff, just the things that matter to installers, distributors, and system integrators. If there's something you'd like to see covered, drop us a line — we read every reply.

Copyright @ 2026 GreenMore All Rights Reserved. Network Supported

Sitemap / Blog / Xml / Privacy Policy

leave a message

leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
submit

Home

Products

WhatsApp

contact