Large-area BIPV curved solar tile roof array for commercial buildings by GreenMore
Home

solar roof tile waterproofing

solar roof tile waterproofing

  • BIPV Roofs Rarely Fail on the Electrical Side
    BIPV Roofs Rarely Fail on the Electrical Side Nov 06, 2026
    L Luke Product Manager, GreenMore · Photovoltaic building materials Thin-film three-curve solar tiles are one of the most architecturally integrated BIPV options on the market. Their curved CIGS (copper indium gallium selenide) layer, ETFE front film and laminated edge sealing let them replace conventional roof tiles while generating electricity. That multi-layer build is exactly what makes them attractive — and what introduces a specific failure mode that project teams should understand: ETFE surface delamination, commonly described on site as "peeling" or "lifting." In almost every case it starts at the edge rather than at the cell, and it takes a season or two before anyone notices. By the time it is visible on the roof, the area that has actually failed is usually larger than the area you can see. The front film has peeled back to a pale patch on one tile, and the edge seal beside it has cracked. What a CIGS Three-Curve Tile Is (and Why It Has Layers) A curved solar tile is not a flat panel bent into shape. It is a laminated composite built from the outside in: ETFE front film — a transparent, chemically inert fluoropolymer that protects the cells from UV, moisture and abrasion while transmitting light to the active layer. Encapsulant layer — typically EVA, PVB or a specialty adhesive that bonds the ETFE to the active cell layer. CIGS thin-film cell — the semiconductor that actually generates electricity. Back substrate — the structural base that gives the curved tile its shape and mechanical strength. The curved profile adds a permanent bending stress that flat panels do not carry. ETFE is chemically inert by nature, which is a good thing for durability, but it also means the surface must be specially treated (corona, plasma or primer) before the encapsulant will bond to it reliably. If that surface treatment is inconsistent, the interface between ETFE and encapsulant becomes the weakest link in the stack. Think of it as a multi-layer sticker on a curved surface. If the adhesive at the edge starts to lift, moisture and air get under the layers, and the lifting spreads. In a solar tile, that "lifting" is delamination. Curved tiles are not built on one cell technology alone. CIGS is the thin-film route; back-contact crystalline is the other, and the two behave differently once they are on a roof. A comparison of the two routes covers where each one makes sense. How to Recognize Delamination on Site Delamination has a recognizable appearance that differs from common surface defects. The main visual signs are: Irregular whitish or opaque patches on the tile surface where the ETFE film has separated from the encapsulant beneath. Visible bubbles or blisters under the ETFE film, often starting at edges and growing inward. Edge seal failure — cracking, peeling or lifting of the side sealing material, sometimes with moisture visible under the seal. Progressive spread — small affected areas that grow over weeks or months, especially after rain events. These signs are distinct from other common issues: Issue How it differs from delamination Surface dirt or bird droppings Washes off; does not affect film adhesion Scratches or abrasion Linear marks on the ETFE surface, no separation Hail damage Localized puncture or crack, usually with a clear impact point Hot-spot yellowing Discoloration of the cell layer, no film lifting Visual inspection is the first step. Where delamination is suspected, two lab tests give a clearer picture: EL (electroluminescence) imaging — reveals micro-cracks and inactive areas in the CIGS cell beneath the delaminated zone. Insulation resistance (IR) testing — checks whether moisture ingress has compromised the electrical isolation of the cell layer. Four defects that get mistaken for each other. Only the fourth is delamination. The Full Failure Chain: From Intact Tile to Peeling ETFE Delamination is rarely a single-cause event. It is a chain of conditions that, once started, tends to accelerate. Step 1 — Edge Seal Compromise (the usual starting point) The side seal is the first barrier against moisture. If it degrades, cracks, or is mechanically damaged during installation, rain and humidity can enter the tile interior along the edge. Edge ingress is the dominant moisture path in fielded modules, and the mechanism is well documented by the US Department of Energy. Once water reaches the ETFE–encapsulant interface, it begins to hydrolyze the adhesive bond. Encapsulants are designed to be moisture-resistant, not moisture-proof at a compromised edge. The bond weakens progressively rather than failing all at once. Studies of EVA adhesion under combined UV, heat and humidity show the same pattern: the loss is cumulative, not sudden (OSTI). Step 2 — Three Acceleration Factors Once the seal is breached, three categories of factor determine how quickly and how far delamination spreads. At the factory Lamination process limits on curved tiles. Flat modules are laminated in well-established cycles of vacuum, temperature and pressure. Curved tiles introduce uneven pressure distribution across the curvature. If vacuum level, temperature profile or hold time is insufficient, the encapsulant may not cross-link completely, leaving the bond weaker than specified from day one. ETFE surface treatment variability. If the corona or plasma treatment of the ETFE is uneven across a batch, some tiles will have lower initial adhesion than others — a latent defect that only shows up after months in the field. Edge seal material selection. Not all sealants perform equally under UV, thermal cycling and hydrolysis. A sealant chosen primarily on cost rather than on long-term weathering data can become the limiting component. On the roof, where most cases start Uneven batten or rail installation. A curved tile forced onto a non-flat substrate carries mechanical stress in the glass and the lamination. That stress concentrates at the edges, where the seal is. Over-tightening of fixings. Clamping force beyond the tile's design tolerance can micro-crack the edge seal or distort the curvature, both of which open pathways for moisture. Poor overlap drainage design. If adjacent tiles do not shed water cleanly, water can pool at the joint and sit against the edge seal for extended periods — exactly the condition that accelerates hydrolysis. Foot traffic during installation. Walking directly on tiles can cause micro-damage to the ETFE or edge seal that is invisible at handover but becomes a failure origin months later. In the climate Thermal cycling. Day–night and seasonal temperature swings cause the different materials in the tile (glass, ETFE, encapsulant, CIGS, substrate) to expand and contract at different rates. Each cycle slightly strains the bonded interfaces. Over thousands of cycles, fatigue accumulates. UV exposure. Long-term UV gradually reduces the flexibility and adhesion of some encapsulants. This is a slow process (years, not months), but it lowers the threshold at which other factors trigger failure. High humidity and freeze–thaw. In humid climates, moisture ingress is faster. In cold climates with freeze–thaw cycles, water that has entered a small defect can freeze, expand, and mechanically widen the defect. Step 3 — Single-Event Triggers (less common but possible) A single impact event — hail, a falling branch, dropped tools during maintenance — can create a small breach in the ETFE or edge seal. If the breach is not detected and sealed, it becomes a new entry point for moisture, and the delamination process begins from that point. Where moisture gets in. A failed edge seal opens a path along the ETFE–encapsulant interface. What Happens After Delamination Starts The consequences are not cosmetic. Once the ETFE separates from the layers beneath, the tile stops working as a panel and as a roof at the same time. Power Output Declines The delaminated zone no longer transmits light cleanly to the CIGS cell. Output from that area drops. If moisture reaches the cell layer itself, it can corrode the thin-film electrodes, causing a progressive and irreversible power loss that extends beyond the visibly affected area. Electrical Safety Risks Increase Moisture inside the tile reduces insulation resistance. In a string of tiles at system voltage, reduced insulation can lead to leakage current to ground or, in the worst case, DC arcing at a damaged interconnect. Both conditions are safety issues, not just performance issues. Roof Waterproofing Is Compromised The tile is simultaneously a power generator and a roof covering. A failing edge seal means the tile is also failing as a waterproofing element. Water that enters through a delaminated edge can migrate into the roof structure, with consequences for insulation, battens and the building interior. Why Replacement Beats Repair A delaminated tile cannot be reliably repaired on the roof. The multi-layer bond cannot be restored in situ. The correct response is replacement of the affected tile(s) and investigation of why the failure started, so the same issue does not recur across the installation. How to Prevent Delamination on BIPV Projects Product Selection Ask the manufacturer about the lamination process for curved tiles specifically, not just flat modules. Curvature changes the pressure profile. Request data on ETFE surface treatment consistency across production batches. Confirm the edge seal material specification and whether it has been tested for hydrolysis resistance, UV aging and thermal cycling — not just initial adhesion. Where available, review accelerated aging test results (damp heat, thermal cycling, humidity-freeze) for the specific tile model. For thin-film CIGS, the applicable test basis is IEC 61215-1-4, which adds CIGS-specific requirements on top of the general module tests. Profiles, colours and datasheets for the current range are listed under solar tiles. Design and Detailing Ensure the support structure is flat within the tile manufacturer's tolerance. A curved tile on a non-flat substrate carries built-in stress. Specify overlap and drainage details that prevent water from pooling at tile joints. Design fixing points and clamping forces within the tile's rated limits — not based on generic framing practice. Installation Practice No walking on installed tiles. Use crawl boards or roof ladders where access is needed. Control fixing torque to the manufacturer's specification. Over-tightening is a common and avoidable cause of edge damage. Protect edge seals during handling and stacking. Once an edge is nicked or compressed, the tile's moisture barrier is already compromised before it reaches the roof. Operations and Maintenance Visual inspection of edge seals at least annually, and after any severe weather event. Periodic EL and insulation testing on a sample of tiles, especially in the first two years when latent manufacturing defects are most likely to surface. Keep installation records including batch numbers and tile positions, so that if a failure pattern emerges, it can be traced to a specific production run or installation team. Edge sealing decides how long the tile lasts, and it is still done by hand, on the roof. Field Checklist for Project Teams When delamination is reported or suspected on a project, the following steps help separate a single-event damage case from a systemic issue. Step What to do What it tells you 1 Map the extent One tile points to impact. A cluster on one roof plane points to drainage or substrate flatness. Spread across orientations points to the product or the sealant. 2 Check overlaps and fixings Ponding water, distorted tiles or over-tightened clamps in the affected area. 3 Record batch and installation dates Lets you cross-reference other projects built from the same production run. 4 Send samples for lab testing EL imaging, insulation resistance and damp-heat aging separate adhesion failure from moisture corrosion. 5 Set the replacement scope Affected tiles plus same-batch tiles showing early signs, with the root cause fixed before anything goes back on. A Tile That Has to Do Two Jobs A BIPV tile is a building component, and that is the harder job of the two. A roof that leaks has failed, whatever the meter says. That means the materials, the manufacturing process, the roof design, and the installation all have to be right. Most cases have more than one cause, and the fix is never a single step. GreenMore builds curved CIGS thin-film tiles and BC three-curve tiles at its own plant, and supplies BIPV projects in Europe and the Middle East. Our role as the tile manufacturer is to stay in the project from the early feasibility stage — reviewing roof design, confirming product suitability, and providing technical guidance through installation and commissioning — rather than shipping a pallet and walking away. For partners planning a curved solar tile roof, we can review the roof layout, confirm the tile model and configuration, and provide a project-specific proposal. Reach us through our contact page or at export@gmsolarkit.com. For how that looks on a finished roof, see the Israel home solar roof project. Non-standard profiles, colours and fixing details are handled under customised services. Frequently Asked Questions Can a delaminated solar tile still generate electricity? Partially, yes. The undamaged areas of the tile will continue to produce power. But the delaminated zone no longer contributes, and moisture ingress can progressively corrode the cell layer. A delaminated tile should be replaced rather than left in service, both for performance and for electrical safety. Can delamination be repaired on the roof? No. The multi-layer bond cannot be restored in situ. Attempting to re-seal or re-laminate a delaminated tile on the roof does not restore the original adhesion or insulation properties. The correct action is tile replacement. Which climates need the most attention to edge-seal reliability? High-humidity coastal regions, areas with large day–night temperature swings (desert climates), and regions with freeze–thaw cycles all accelerate the conditions that lead to delamination. Projects in these climates should place extra emphasis on edge-seal material selection, overlap drainage design, and post-installation inspection. How long does it take for delamination to appear? Latent defects from lamination or ETFE surface treatment usually surface within the first two to three years, often after the first hot season followed by the first wet one. Damage caused during installation or by a single impact can appear within months. If a tile is going to peel, the first two years are when it shows. Updated November 11, 2026 Standards referenced: IEC 61215 (module design qualification), IEC 61730 (module safety qualification), EN 14782 (self-supporting metal sheet for roofing).
  • When a BIPV Project Fails: Spares, Timelines, Repair Costs
    When a BIPV Project Fails: Spares, Timelines, Repair Costs Jul 16, 2026
    Every supplier publishes what its support covers. Very few publish what happens when something actually fails: who answers, how long it takes, what the part costs, and who pays for the flight. That is what this page is about. It is not a list of services. The service and support page covers what GreenMore offers across planning, installation, commissioning and operation, including the training programme, documentation set and warranty terms. This page takes one narrow subject: the failure path, from the first message to the part arriving on site, with the timelines and costs attached to each step. If you are evaluating whether the support package is adequate, read the service page. If you are planning a project and want to know what a bad week looks like and what it will cost, read this. Most cases are resolved with three things on the table: the drawing, the log and a photograph. How a factory-based support model behaves GreenMore is a factory, not a service network. There are no regional service partners and no local stock of every part in every market. What exists is an engineering team at the plant that has built and commissioned these systems, reachable by email, messaging and video call, with a typical response time of 24 hours on business days. Four consequences follow, and they are better understood before a project starts than after: Response time is about a day, not an hour. A fault raised on Friday evening is answered on the next business day. For a residential system that is fine. For a commercial system losing revenue per hour, it argues for holding spares on site. English is the working language. For other languages we work through a translator or machine translation. That is adequate for documents and written questions and slow for a live fault-finding call. The first reply usually comes from your sales contact. Not because engineers are hidden, but because not every engineer is confident speaking English, and a routed question gets an accurate answer faster than a direct one that gets misread. There is no local technician to send. Remote diagnosis is the default. An engineer attends site only when remote work has been exhausted, and the travel is charged at cost. None of this is unusual for a manufacturing exporter. It is unusual to see it written down. The five failures behind most support tickets Across the projects we support, the same handful of problems keeps appearing. They are worth knowing because four of the five are installation errors rather than product faults, and all five are cheaper to prevent than to fix. 1. Communication that works but does not report The system generates, the inverter display looks normal, and the monitoring platform shows nothing. The usual causes are RS485 or CAN wiring reversed, termination resistors missing at the end of a long bus, or a meter address set to the wrong channel. This is the most common ticket we receive, and it is almost always resolved remotely in one session. It is also the one that damages trust most, because the owner concludes the system is broken when it is only unobserved. 2. Firmware mismatch between inverter, battery and EMS Everything energizes, then the battery refuses to charge above a set rate because two devices disagree about the protocol version. Nothing is faulty. The fix is a version alignment, which takes minutes once identified and can take two weeks to identify if nobody thought to check the firmware builds against each other. 3. The CT clamp that charges when it should export Fitted backwards, or clamped to the wrong conductor. The system behaves correctly according to what it measures and incorrectly according to what the building needs. On a sunny commissioning day this is invisible. On the first evening it is obvious, and by then the installer has left. The same clamp logic applies to the residential storage systems, where import and export direction decides whether the battery charges or discharges. 4. String voltage that is fine in summer A string designed at 25 degrees can exceed the inverter window at minus 10. The commissioning reading looks acceptable, the system runs all summer, and the first cold snap takes the inverter out. This one is not an installation error at all: it is a design error that no amount of site work will correct. The check is simple and worth doing on every project. Take the module open-circuit voltage at STC, apply the temperature coefficient at the lowest expected ambient for the site, multiply by the number of modules in the string, and compare against the inverter maximum. If it is close, shorten the string. 5. The roof detail that leaks at the valley Cut tiles at a hip or valley are unavoidable. What matters is whether the cut lands on a lap or on an exposed face. A cut through the drainage channel will track water sideways, and the leak appears a metre away from where it was made. The BC curved tile carries its channel along the vertical lap for exactly this reason, which is why the cutting sequence matters more than the cutting tool. This is the only one of the five that genuinely requires a site visit in most cases, because it cannot be seen remotely. Four of the five common failures can be diagnosed from a photograph and a log. The fifth cannot. What a usable support request contains The single biggest cause of delay is a request that cannot be actioned. Not a difficult fault, not a slow engineer: a message without a serial number. Without it we cannot tell which firmware build, which batch or which production revision the unit came from, and the first reply becomes a question instead of an answer. A request that gets resolved in one round contains six things: Model and serial number. Every unit, including batteries and inverters, not just the one that looks faulty. Fault code or error text. Photographed from the display or exported from the platform, rather than paraphrased. A log extract covering the period before the fault. The hour before an alarm usually explains it. Photographs. The installation, the connector in question, the label plate, and the reading on the meter. What changed. New firmware, new load, new tariff setting, grid outage. Most faults have a trigger. Site conditions at the time. Weather, ambient temperature, snow cover, and whether the grid was stable. With those, most cases close in one exchange. Without them, the case becomes a conversation, and a conversation across time zones costs days rather than hours. How long each kind of case takes These are working figures for a business-day timeline, from the moment a complete request arrives. They are not service-level commitments, and a case that turns out to be a hardware failure takes longer than one resolved by configuration. Case type First response Resolution What shortens it Monitoring or communication fault Within 24 hours Same session in most cases Log extract, platform access, photographs Firmware or configuration issue Within 24 hours 1–3 days Current versions of all three devices Suspected hardware failure Within 24 hours Diagnosis in 1–2 days, part lead time after Serial number, fault history, meter readings Roof or waterproofing issue Within 24 hours Site visit or installer rework Photographs of the detail, not the roof Spare part quotation Within 24 hours Dispatch depends on stock and shipping Model, quantity, destination, order reference Out-of-warranty repair Within 24 hours Assessment first, then part and travel Fault history, photographs, site access Two things are outside this table and should be planned separately: shipping time, which depends entirely on destination and customs, and site attendance, which depends on visas and flight availability. Neither can be compressed by working faster. Language, and who you end up talking to English support means English support. Most of our engineers read technical English well and speak it with varying confidence. For a drawing, a written diagnosis or a document, that is not a limitation. For a live fault-finding call with three people on a roof in the rain, it is. In practice the route is: your sales contact receives the question, identifies whether it is installation, commissioning, configuration or hardware, and routes it to the right engineer. When the problem is genuinely difficult, the engineer joins directly and the sales contact stays on the call as translator. That is why the first reply often comes from a commercial contact rather than a technical one. Two things make this work better. Written questions get written answers, which are accurate and can be forwarded to the installer. Live calls are scheduled rather than improvised, so a translator is available. If the installation team does not work in English, nominate one English-speaking coordinator on your side. It costs less than a call-out. Spare parts: two models and the arithmetic There are two ways to handle spares, and the right choice depends on how far the site is from the factory and what a day of downtime costs. Model one: pre-purchased with the order A percentage of the order quantity is configured as spares at the time of purchase, typically 3 to 5 percent depending on project size and criticality. They ship with the main consignment, clear customs with it, and sit on site from day one. This is the right model for remote projects, for projects where the installer is not local, and for anything where a two-week wait for a part is unacceptable. The cost is visible in the quotation up front, which some buyers resist, but it is the cheapest way to guarantee a same-week repair. Model two: factory stock, shipped on demand No spares are purchased in advance. Parts are held at the plant and dispatched when a failure is confirmed. This suits distributors with a local warehouse, projects on a fast shipping lane, and buyers who would rather not tie up capital in stock that may never be used. The trade-off is time. A part that has to be quoted, invoiced, packed and shipped internationally will not arrive this week. For a commercial system with a revenue loss per day, that arithmetic usually settles the question in favour of model one. Pre-purchased spares ship with the main consignment and clear customs with it. What spares cost Spare parts are not free, including during the warranty period. The warranty covers the defective part; it does not cover a stock of replacements held on site. Pre-purchased spares are charged at the time of order and discounted against the project, with the discount depending on volume and mix.   Pre-purchased with the order Shipped from factory stock Quantity Typically 3–5% of order As required Shipping Travels with the main consignment Separate shipment, separate customs Cost timing Paid with the order, discounted Charged when the part is needed Best for Remote sites, non-local installers, high downtime cost Local distributors, short shipping lanes, low downtime cost Lead time after failure Same day, part already on site Quotation, then production and shipping Repair after the warranty ends Batteries, hybrid inverters and ESS cabinets carry a three-year warranty. Solar roof tiles carry a 25-year linear power warranty. Once those have expired, or where a fault is not covered, repair is charged at cost: no margin on the part, no fixed call-out fee. There are two routes, priced differently. Remote support. Diagnosis, configuration guidance and firmware work over email, messaging or video call. Provided without charge beyond the component cost, because it costs engineering time rather than travel. Engineer on site. Used when the problem cannot be resolved remotely. The engineering time is not the expensive part. The travel, accommodation, visa and local transport are, and those are charged to the buyer at cost. The practical advice is to exhaust the remote route first. Most faults that look like they need a site visit turn out to be configuration or communication problems that a scheduled call with the right photographs will resolve. Where attendance is genuinely required, the travel cost is quoted before anything is booked, so there is no invoice surprise afterwards. Requests start on the contact page, with the model and serial number in the first message. Where this model fails Being specific about the limits is more useful than another list of capabilities. No 24/7 coverage. A fault on Friday evening is answered on the next business day. Acceptable for residential; for commercial systems with revenue at stake, it argues for pre-purchased spares and a local technician who can act on written instructions. No regional service network. There is no partner in your country who can arrive the same day. If that is a project requirement, it has to be built locally, and it is better to know that at quotation stage. Language limits on live calls. Written English is not a constraint; a spontaneous technical conversation in a second language is. Schedule calls and involve a translator where needed. Support is not a substitute for a competent installer. Four of the five failures above are installation errors. The engineering team can diagnose and advise, but it cannot install a roof remotely, and the biggest determinant of how a project goes is who is on the roof. For the installation side of that equation, see how the tile system is installed by one person. For the approval and sample stage that comes before a project order, see how sample customization works. For customization scope and certification by market, see the full-chain customization guide. For territory and stock terms, the distributor programme covers the commercial framework. Frequently asked questions How quickly does GreenMore respond to a technical question? Typically within 24 hours on business days, and that means a substantive answer rather than an acknowledgement. Requests that arrive with a model number, serial number, fault code and photographs are usually resolved in the first reply. Missing serial numbers are the most common cause of a second round of questions. What languages does technical support cover? English is the working language. For other languages we work through a translator or machine translation, which is fine for documents and written questions but slow for a live fault-finding call. If the installation team does not work in English, nominate one English-speaking coordinator on the buyer side and schedule calls rather than improvising them. Should I buy spare parts with the order? If the site is remote, the installer is not local, or downtime has a real cost, yes. Pre-purchased spares are typically 3 to 5 percent of the order quantity, travel with the main consignment and are discounted against the project. If you hold a local warehouse or the project is on a fast shipping lane, factory stock shipped on demand is usually cheaper overall. Are spare parts free during the warranty period? No. The warranty covers the defective part, not a stock of replacements held on site. Pre-purchased spares are charged at the time of order and discounted against the project. Replacement of a covered failure is provided under the warranty terms, but spares held in reserve are not. What happens after the warranty expires? Repair is charged at cost, with no margin on the part and no fixed call-out fee. Remote diagnosis and configuration support are provided without charge beyond the component cost. If an engineer needs to attend site, travel, accommodation and local transport are charged to the buyer at cost, quoted before anything is booked. Can I speak directly to an engineer? Yes, for installation difficulties, commissioning problems and confirmed faults. Day-to-day questions normally go through your sales contact, who routes them to the right engineer and stays on the call as translator where needed. Direct engineer sessions are scheduled rather than immediate, so bring the drawing, the fault log and photographs. S Smith Technical Director Leads engineering support from system planning through long-term operation, reviewing designs and commissioning plans with partners before energizing. Updated on November 14, 2026

Subscribe To Our Newsletter

Stay up to date with GreenMore. We share new BIPV solar tile releases, product and certification updates, and field notes from our projects — no fluff, just the things that matter to installers, distributors, and system integrators. If there's something you'd like to see covered, drop us a line — we read every reply.

Copyright @ 2026 GreenMore All Rights Reserved. Network Supported

Sitemap / Blog / Xml / Privacy Policy

leave a message

leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
submit

Home

Products

WhatsApp

contact